Wavetronix SMARTSENSOR 105 Uživatelská příručka Strana 20
- Strana / 107
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
CHAPTER 1 INSTALLING THE SMARTSENSOR MATRIX 19
Figure 1.6 – Sensor 6-conductor Cable Connector
To set up your network in an orderly fashion, it is recommended that labeling be used on
the service end of each SmartSensor 6-conductor cable. A convenient way to label the
cables is to mark the last seven digits of the serial number on each sensor and the direction
of trac monitored (see Figure 1.7).
Figure 1.7 – Service End Labeling
Grounding the Sensor
e SmartSensor Matrix must now be grounded:
1 Connect a grounding wire to the grounding lug on the bottom of the sensor (see
Figure 1.5).
2 Connect the other end of the grounding wire to the earth ground for the pole that
the sensor is mounted on. Do not attempt to run the grounding wire back to the main
trac cabinet.
- SmartSensor Matrix 1
- Contents 4
- Introduction 6
- SmartSensor Matrix Package 7
- Selecting a Mounting Location 8
- Sensor Pole 9
- Figure I.3 – Corner Radar 9
- Installing the SmartSensor 12
- In this chapter 14
- Sensor Mounting Guidelines 15
- Front edge of field of view 18
- Grounding the Sensor 20
- Connecting Power and 22
- Surge Protection 2 22
- Mounting the Backplate 23
- Connecting AC Power 23
- SSMatrix #2 29
- SSMatrix #3 29
- SSMatrix #4 29
- Channel 33
- Bus 1 Bus 2 33
- Click 112 DIP Switch Settings 34
- Click 112/114 LEDs 37
- Click 104 LEDs 39
- Channel Mapping 40
- Using SmartSensor Manager 44
- Installing SmartSensor 46
- Manager Matrix 4 46
- Using the Click 421 47
- Installing SSMM 48
- Figure 4.4 – Shortcut Options 49
- Microsoft .NET Framework 50
- Communication 5 52
- Serial Connection 54
- Internet Connection 57
- Address Book 59
- Virtual Sensor File 60
- Communication Error Log 62
- Figure 5.12 – Error Log 63
- Chapter 10) 65
- Sensor Settings 6 66
- Comm Sensor Settings 67
- Sensor Info Screen 68
- Lanes & Stop Bars 7 70
- Edit Area 71
- Saved Configuration Overlay 72
- Capturing Lanes and Stop Bars 73
- Saving the Configuration 74
- Moving the Sensor View 75
- Editing Thresholds 76
- Automatic Configuration 77
- Adding/Deleting/Moving a Lane 78
- Moving a Lane Node 80
- Zones & Channels 8 82
- Menu Bar 83
- Placing Zones 84
- Editing Zones 85
- Placing AutoZones 85
- Normal Channel 86
- Counting Channel 86
- Pulse Channel 86
- Channel LED 87
- Editing Channels 88
- Output Settings 89
- Measuring Zones 90
- Figure 8.15 – Using Flags 91
- Verification 9 92
- Channel Indicators 93
- Verification Menu Bar 94
- Tools 10 96
- Backup/Restore 97
- Using the Rack Card Tool 98
- Firmware Version 99
- Signal Cards Switch 99
- Channel Outputs Switch 100
- Tracker Logging 100
- 100 CHAPTER 10 TOOLS 101
- Figure 10.7 – Log File 101
- Sensor Self Tests 102
- Appendix 104
- Creating Custom Cables 105
- Appendix B – Cable Lengths 106
- 106 APPENDIX 107
- Figure C.1 – The Click 221 107
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Wavetronix SMARTSENSOR 105
(36 stránky)
(12 stránky)Dynex DX-WLOM2 - Wireless Optical Mouse Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Mäuse Dynex DX-WLOM2 - Wireless Optical Mouse.
Wir stellen 1 PDF-Handbücher Dynex DX-WLOM2 - Wireless Optical Mouse zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Betriebsanweisung
Komentáře k této Příručce