Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick Uživatelský manuál stáhnout pdf (Strana 1)

Click 511 Digital I/O Repeater

INSTALLER QUICK-REFERENCE GUIDE

How to use on-device conﬁguration features

is document covers how to set up the client devices, and then how

to set up the server. To do so, you rst need to know the basics of the

device’s conguration features.

e Click 511 has four LEDs that monitor device activity and help

you select tasks and operating modes. It also has two banks of LEDs:

one of yellow LEDs that represent submenu 1 and one of red for sub-

menu 2. It also has a push-button, labeled Mode Switch, also used for

selecting tasks and operating modes.

LED task-indicating functions:

Client – Sets the device as a client (attached to the

digital output device being monitored)

–

Server – Sets the device as a server (used as a base

station)

–

Server Output Setup – Lets you you specify the output

type for server operation

– –

Reset – Release push-button when red LED is blinking

to reset to factory defaults.

Note. How to select and use Client, Server, and Server Output Setup modes will be covered later in this

document. e Reset task can be used at any time to reset the device to factory defaults. If reset, the Click

511 will default to being a client with ID number 1.

www.wavetronix.com

801.734.7200

Select mounting locations

In a Click 511 application, there will be between two and nine devices:

˽ Server – One device will act as a server. is server, located at a base station, will poll the client devices

about the state of their connected digital inputs.

˽ Client – One or more devices (up to eight) will act as clients. ese clients, located close to the digital

output devices being monitored, will report the status of their digital inputs.

Yellow LEDs

Red LEDs

Multicolored LEDs

Button

Main Menu

Sub Menu 1

Sub Menu 2

Continued on next page

1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - Select mounting locations

Click 511 Digital I/O RepeaterINSTALLER QUICK-REFERENCE GUIDE2 How to use on-device conﬁguration featuresis document covers how to set up the client

Strany 2

Select a task or operation function by navigating through the main menu (multicolored LEDs) and the sub-menus (yellow and red LEDs) using the push-but

Strany 3 - Wire client digital inputs

4 Wire communicationsYou must connect each client to a device (such as the Click 400 900 MHz radio) that can convert the serial communications from th

Strany 4

6 Conﬁgure the clientsNext you will congure devices to act as clients. As mentioned in Part 1, each Click 511 installation has one server and between

Strany 5 - Conﬁgure the server

9 Conﬁgure the serverNext, congure a Click 511 to act as a server:1 Hold down the push-button, then release when the blue LED ashes (Server mode).2

Strany 6 - Set up server output

Komentáře k této Příručce

Žádné komentáře

Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick. Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick-reference Guide User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick. Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick-reference Guide User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Wavetronix Click 511 (digital I/O repeater) (CLK-511) - Quick