Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Uživatelský manuál Strana 101
- Strana / 148
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
100 CHAPTER 8 VERIFY CHANNELS-ALERTS-ZONES
Click and hold on the roadway display selector to access the roadway display mode list (see
Figure 8.13).
Figure 8.13 – Roadway Display Mode List for Advance (left)
and Advance Extended Range (right)
Le-click the roadway display button to cycle forward through the available modes; right-
click to cycle backwards through the list (right-clicking is only available on the PC version
of the SSMA soware).
Range (ft) – Displays the range of the associated tracker to the stop bar.
Speed (mph) – Shows the speed of the associated tracker.
ETA (s) – Shows the tracker’s Estimated Time of Arrival (in seconds) to the stop bar.
ID – Displays the ID number of the associated tracker. SSMA assigns a unique ve-digit
identication number (1 to 99999) to each tracker.
Qualified Count – e two types of Qualied Count displays available are Qualied
Count and Dynamic Density. e data displayed on the trackers depends on the type
selected in the Setup CAZ screen.
Discovery Range – Displays the range at which the tracker was rst detected. (Only
available with SmartSensor Advance Extended Range.)
Priority Level – Shows the priority level assigned to a vehicle based upon its discovery
range. Level 1 priority is the highest priority. Level 2 is the highest priority. (Only avail-
able with SmartSensor Advance Extended Range.)
Tri-view – Allows up to three user-specied modes to be displayed on each tracker.
(blank) – Removes all data from the tracker displays.
(disabled) – Disables the trackers on the roadway. However, the LEDs in the right
sidebar will function as normal.
Note
The disabled mode may be useful when communication is slow or unreliable.
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Související produkty a manuály pro Senzory Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
Senzory Wavetronix VDR24 Radar Uživatelský manuál
(78 stránky)
(78 stránky)
(4 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce