Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Uživatelský manuál Strana 102
- Strana / 148
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
CHAPTER 8 VERIFY CHANNELS-ALERTS-ZONES 101
Qualified Count
When the Channel LED is activated in the right sidebar, the Qualied Count value will
always be displayed as “---” because a channel may consist of up to 16 zones and the exact
meaning of a channel’s Qualied Count is undened.
When using the Qualied Count display mode, the rst number on the tracker represents
the number of qualied detections in the zone and the number in parentheses represents
the amount of trackers needed to meet the dened requirements. If the number of qualied
detections is below the Qualied Count minimum, the number in parentheses is preceded
by a “-”; if the number of qualied detections is higher than the Qualied Count maximum,
the number in parentheses is preceded by a “+”; if the number of qualied detections is in
between the Qualied Count minimum and maximum settings, a “0” is displayed.
Figure 8.14 describes the numbers displayed when the qualied count is lower than, within
the limits of, or higher than the specied settings.
Detected
Qualified Count
Qualified Count
Minimum
Qualified Count
Maximum
Displayed Text
1 2 4 01 (-01)
3 2 4 03 (00)
6 2 4 06 (+02)
Figure 8.14 – Display Text for Qualified Count Zone Types
Note
When the selected roadway display mode shows the qualified count value on the
detection, the tracker highlighting indicates whether the specific detection meets
the range, speed, ETA, and priority level qualifications of the associated zone. High-
lighting on an individual tracker does not indicate whether or not there are enough
qualified detections to satisfy the qualified count filter for the zone.
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Související produkty a manuály pro Senzory Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
Senzory Wavetronix VDR24 Radar Uživatelský manuál
(78 stránky)
(78 stránky)
(4 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 1.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce